The Problem That Sounds Like a Feature
Multipoint Bluetooth was supposed to solve a specific annoyance: the moment you pick up your phone while your earbuds are connected to your laptop, they should switch automatically. Same instant your phone is in front of your face, audio should flow from the phone, not the laptop. No manual disconnection. No twenty seconds of dead air while the system figures out what just happened.
Most earbuds with multipoint support do this now. Samsung Galaxy Buds, AirPods Pro, Sony WF-1000XM5, Jabra Elite 85t. They switch. But anyone who owns two of these devices and uses multipoint regularly knows something goes wrong in the transition. The audio quality drops. The connection hiccups. For a single moment, sometimes two, sometimes three, the sound becomes noticeably compressed, slightly lower bitrate, slightly less present.

Sony WF-1000XM5 True Wireless Earbuds

Apple AirPods Pro (2nd Generation)
Then it recovers. By the time you've consciously noticed it happened, the earbuds have already re-negotiated the codec and you're back to full quality. But you noticed. You heard it. You know something weird just happened even if you can't articulate exactly what.
That something is a codec negotiation failure hiding behind a very visible symptom.
Why Codecs Matter More Than Bitrate
A Bluetooth codec is the algorithm that compresses audio on the transmitting device and decompresses it on the receiving device. The codec isn't just about how much compression happens; it's about what kind of compression, what information the algorithm discards, and how well the decompressed audio approximates the original signal.
aptX Adaptive, which Qualcomm developed for high-quality wireless audio, dynamically adjusts the bitrate between 279kbps and 420kbps depending on available bandwidth. When the connection is clean, you get 420kbps and can stream 24-bit audio. When interference appears, the codec drops to 279kbps automatically, preserving connection stability at the cost of some audio fidelity. The switch happens in milliseconds and most listeners never consciously notice it.
LC3 is Bluetooth 5.2's new codec, designed from the ground up for LE Audio. It's lower complexity, hence the name, which means it requires less processing power and less battery. A hearing aid using LC3 can run for days on a single charge instead of hours. LC3 was designed with medical devices as the primary use case, but consumer manufacturers immediately saw its efficiency and started building it into high-end earbuds.
The problem appears when a single earbud needs to support multiple codecs simultaneously. Your phone might prefer aptX Adaptive because the connection is strong and audio quality is the priority. Your laptop might only support SBC, the basic Bluetooth audio codec that every Bluetooth device supports as a fallback. Your earbuds support all three.
When you're connected to both, your earbuds are maintaining two separate audio streams: aptX Adaptive from the phone, SBC from the laptop. The moment you try to switch which one is actively playing, the earbuds need to drop one audio stream and activate the other. That's when codec negotiation has to happen.
The Negotiation That Fails Under Pressure
Ideally, the device you're switching to already has an established Bluetooth connection ready to go. The codec for that connection should already be selected. In theory, activation is instant. In practice, several things can go wrong simultaneously. The connection to the new device was successfully paired but the codec was never properly negotiated during that pairing. The new device changed its codec preference since the last time you connected: Qualcomm pushed a firmware update to your phone that now prefers LC3 over aptX, and your earbuds are trying to negotiate a codec that your phone doesn't actually support in the current firmware version.
Or the connection bandwidth has degraded since you last used that device. Your laptop is now experiencing interference from a microwave oven operating in the same 2.4GHz frequency band, and aptX Adaptive would be the ideal codec choice, but the negotiation protocol defaults to the lowest-common-denominator codec when there's any uncertainty. So it falls back to SBC, which is technically compatible with everything but sounds noticeably worse than either aptX or LC3.
That moment of degradation, that perceptible drop in audio quality during the switch, is the codec negotiation failing to find the best common codec between the two devices and temporarily defaulting to SBC while the hardware figures out what to do next.
Why Manufacturers Won't Tell You This Is Happening
Because admitting that your premium $300 earbuds occasionally sound like $50 budget earbuds for the two seconds it takes to switch devices is not a strong marketing message. Instead, manufacturers publish spec sheets that say "supports aptX, LC3, AAC, SBC" without mentioning that the codec switching logic has edge cases where it picks SBC under conditions the manufacturer never specified.
Apple handles this differently with the AirPods Pro because Apple controls both the transmitting device (iPhone, iPad, Mac) and the receiving device (the earbuds). When you're switching between two Apple devices, the codec negotiation happens on Apple's terms using Apple's implementation. The probability of negotiation failure drops dramatically because the variables are controlled.
On Android, multiple manufacturers make the transmitting devices (Samsung, Pixel, OnePlus, Motorola), each with potentially different codec implementations, connecting to earbuds made by a different manufacturer entirely (Sony, Samsung, Jabra, Technics). The number of potential failure states in that matrix is very large.
The LC3 Acceleration and What It Means
LC3 adoption is accelerating specifically because of this multipoint problem. If every device used the same codec, negotiation would be trivial. Samsung is pushing LC3 heavily because it controls enough of the Android ecosystem to make a push toward standardization. Sony includes it in the newer WF-1000XM6 specifically to hedge against multipoint codec negotiation failures.
The hearing aid industry's adoption of LC3 was supposed to take until 2026 for widespread market penetration. Instead, it's happening now. FDA approval fast-tracked several LE Audio hearing aids in late 2025, and manufacturers are rapidly deploying LC3 support because the efficiency and interoperability advantages are too significant to ignore.
This has a downstream effect on consumer earbuds: as LC3 becomes the ambient standard for Bluetooth 5.2 devices, the codec negotiation logic becomes simpler. If the worst-case scenario is that you fall back to LC3 instead of SBC, the audio quality drop is barely perceptible instead of dramatic. The codec war isn't being won by aptX or AAC. It's being won by the codec that achieves sufficient quality with the lowest complexity, and that's LC3.
What to Do Right Now
If you own earbuds with multipoint support and you're experiencing audio quality drops during device switching, first step is to check which codec is actually negotiating. Most premium earbuds have a companion app that displays the active codec. If you see SBC during the switch, that's your confirmation that codec negotiation is failing and defaulting to the worst common denominator.
Second step: check for firmware updates on both the earbuds and the devices you're switching between. Qualcomm, Apple, and Sony all push firmware updates to improve codec negotiation logic and increase the likelihood that the algorithm picks the optimal codec instead of falling back.
Third: if you're buying new earbuds in 2026 with multipoint as a priority, prioritize LC3 support explicitly. Ask in the spec sheet whether the earbuds support both LC3 and your phone's preferred codec. If the salesperson doesn't know what you're asking about, find a different salesperson. The ones who understand codec negotiation know how significant this detail is.
The future of multipoint is straightforward: as LC3 becomes standard, codec negotiation becomes more reliable. The moment all your devices speak the same codec language, switching between them becomes genuinely seamless. That transition is happening right now, invisibly, through firmware updates and new device releases. The audio quality drops you're hearing now are a temporary effect of that transition period. They'll be gone by 2027.

